• The migration to this new platform is complete, but there are a lot of details to sort out. If you find something that needs to be fixed make a post in this thread. Thank you for your patience!

Keshe Off Grid Magrav Power System Construction

Appleheads

Interiora
Hermetic Pilgrim
Mysterious Stranger
Joined
Jan 5, 2024
Messages
50
Keshe materials off grid magrav unit construction.

After years of free energy research I have decided to focus on constructing a Magrav system. It consists of many subtleties in the construction, and steps that can easily be overlooked or forgotten. It allegedly can produce power without mains.

The first step for me is the development of the Materials needed.

GANS
I have read the GANS is defined as
(Gas as Nano Solid) or
(Gas as Nano State) or the combination of the two
(Gas as Nano State Solid)

I need to make copper oxide GANS, Iron oxide GANS, Zinc oxide GANS and the coveted CO2 GANS.

The Copper GANS is simple enough to make,

The zinc GANS is also quite simple

The Iron GANS is easy to make.

Though I have successfully created the last three GANSes, where I have come into a struggle is producing the CO2 GANS. I never had green led lights and there are many variables that change the outcome.

Variables include

-Sea Salt content:I have read between 0-14-16% by weight.

-The plates must be similar size and weight

-the distance between the two plates must be optimal

-The connection should have a green or red led between them with the negative on the Nano plated copper and the positive on the zinc plate.

Now Zinc easily degrades into zinc oxide in salt solution. But the people who have replicated the work say that Co2 can be achieved by carefully following the exact instructions.

It can take many Months to produce a sizable amount of the correct CO2 Gans.

I have watched the knowledge seekers workshops on youtube and there are hundreds so it can be a challenge to sift through all of it.

The videos that have changed my thinking about this concept of the Magrav energy systems are as follows

Warning, these videos get loud!








The last video is my favorite of the series. Douglas went to Washington DC to reveal the unit. Unfortunately his unit broke down before he could show it at the conference. The lawyers for the Keshe Foundation did get to witness it.

He hasn’t made a peep since, probably was hired by the American Military to develop this technology and has some sort of NDA.

The videos are choppy and not the best quality, he moves the camera a bit too quickly but I think he is onto something.

There have been a lot of detractors of this information but I think these videos give a good proof. If you can disprove them I would like to know how. I would still like to know how he is operating such high wattage without blowing a fuse?

I found out about this though a Veterans Today article series by Gordon Duff. Unfortunately the links to the news site have migrated to a new platform and the older articles were scrubbed. The powers that were got very nervous when this information came out.

People say they have bought stuff from the Keshe foundation and never received working units, but the information was released in teachings so you can make your own. I guess it could be a con, but I am willing to spend my time and energy recreating a step by step guide on how to actually construct the unit.

Knowing how the dis info agents work they can spin anything.

I have a PDF compilation of the necessary info in one place if anyone is interested I can post it.

My experience with nano coating copper and using a multimeter displayed very tiny milliamps of current in a constantly fluctuating pattern. An interesting anomaly. I guess the superconductive carbon coating also acts in some form of capacitance as well as infinitely resistant as well as super conductive.

Stay tuned as I construct first the Off grid Magrav unit
and also following with the construction of a Solid State Magrav Unit, replacing the water pump and refrigerator compressors with electronic parts.

I have all the materials ready to go so I will start first with making the CO2 GANS collection units, followed by coiling the wires for the coil stackers.

I am not sure if I will use caustic coat or fire coat.
The positives of the caustic coat is that it is simpler to get an even coat. The fire coating process takes some finesse and skill to get the correct coating to appear. Mr. Keshe, says the fire coating nano coat is superior to the caustic coat, for energy purposes.

Once coated the nano layers have to be tuned with the addition of adding the leads of the multimeter to the ends of the plates or wires. It is a tricky process so I am developing a way to remember which side is which.

I am focusing on the off grid MAgrav before getting into the Alchemical work because it would be nice to be able to power a water or sand bath or heater with free energy as I go through the work. I will see if it is worth the effort to construct the magrav. Like the Alchemical Work, prayer is used in the construction of the nano materials, which can be off putting to the scientific minded folks. But then my mind says if I have to pray to make it work is it even real or am I just a fool...

Thanks for reading.
 

Appleheads

Interiora
Hermetic Pilgrim
Mysterious Stranger
Joined
Jan 5, 2024
Messages
50
CO2 Gans.

So the first step I have to do is go over the information again. As I go over the information, I see steps I neglected so I am learning as I go.

WARNING: As a cautionary note, these processes involve caustic salts and liquids, boiling water, open flames, and metallic nano vapor material. It is important to wear safety glass and rubber gloves and in general it is a good idea when conducting experiments.



These are some videos that I have found that have the best explanations available.


This is the original video I watched. The process is shown by Armen of the Keshe Foundation.




A more in depth video by Kehse Foundation Australia Plasma school

Part 1:

Part 2:

The two processes are quite similar but there are variations.


After watching the videos again, I realize I need to get some more rubber/latex gloves, drill holes in my copper plates, some plastic tubing to siphon out the liquid so I do not disturb the nano layers on the copper, and perhaps a bigger container. I also need more NaOH.

I have used the small plastic containers and I also have a pickle bucket that seals tight so I think I will get a bigger plastic container to make a better system.

From what I have experienced, the more times I repeat the process of steam coating the better. Also taking a longer time to dry and a continuing to discharge the voltage on the plates for many days past 2-4 days creates a better result.

The process is tedious and I have had to be very careful to follow directions. I think the process could be improved but I am at a loss on how to do that. I used a lid and rigged a hanger so I can take the lid off the container and easily replace the liquid. Now that I see it’s important not to disturb the material, I am thinking of an easier way to perform this operation. I am working on a video showing where I am at in this process.

A little synopsis. In my container of scrap metal, I found some nano copper plates from a previous experiment, I decided to use those again and try to add more layers to the plates, I also used fins (not fans) from a cpu unit that I had as scrap and the plates already had holes in the top. I have used my multimeter and have not found voltage, I guess I should have paid more attention to it. M.T. Keshe said creating Plasma fields is like caring for a puppy. In June 2023 I did a steam bath and steam coat process probably 4 times and then I got busy and forgot about it. The bucket was sealed and was in the sun. I retrieved it from the outside last week so I will see if I can salvage this experiment.

This is the video I made today.

 

Kiorionis

Thoth
Magus de Moderatio
Patron of the Arts
Hermetic Pilgrim
Joined
Jul 5, 2012
Messages
2,727
Cool. Can’t wait for the next video.

But that seems like a lot of fumes! Ever consider booking up some sort of tube/funnel for when you pour the water on?
 

Appleheads

Interiora
Hermetic Pilgrim
Mysterious Stranger
Joined
Jan 5, 2024
Messages
50
Cool. Can’t wait for the next video.

But that seems like a lot of fumes! Ever consider booking up some sort of tube/funnel for when you pour the water on?
Yes, there are quite a bit of fumes. I usually do the process outside but it's freezing right now and I want the material to be at least near to room temperature as I can get it. It's about 48 F in the cellar. I have thought of creating a flow hood to exhaust the fumes. If I continue to do it a lot I probably will. As for the funnel I don't really want to mess with it now, though I might do it when I create my next steam container. Drill a hole in the lid and attach a funnel. I have some stoppers so I could plug the hole after I pour the water and remove the funnel. Yeah I like that thanks!



Here is the next step, the caustic steaming method. I waited 48 hours and then repeated a similar step with variations. Less caustic and less water, while the material is raised about the water so the caustic steam does a layering process. I am not exactly sure why or what it does, but I am following the directions.


After another 48 hours I repeated the caustic steaming method.


I am quite pleased with how the plates are taking the layering. Some of the larger plates are the original plates, I started coating in this fashion around 10 years ago. They are much darker and thicker than they were before. I am hoping to have some containers set up to collect CO2 GANS in the next week or so. I plan on doing a couple more caustic steam baths, then dry the plates slowly while draining the voltage, or tuning the layers. I have heard both words draining and tuning so I am not sure which is the correct wording.

I will attach a pdf of a compilation of pdfs and various pictures from the keshe foundation website and google image searches. I had the file printed into a notebook so I can have a guide without being on a computer. There is more information and blueprints on the keshe foundation website that are not in this pdf. There are also unofficial blueprints specifically the solid state magrav unit by Christian Marino. I think. It could be official but was never released in the english language. So I had to do some translations. Some of the words I could not translate, and some of the symbols on the schematic are archaic in usage so I had to search older electric engineering legends to come up with the correct meaning to figure out which electronic components to purchase. Now that I think of it I wish I wrote it down. I know I bought the right supplies so when I get there I will detail it.
Actually the file is too big so I will find a website to host it.



Here is a link to the official blueprint released in 2015. I think it contains the health and agricultural information as well.

https://blueprint.keshefoundation.org/blueprint.php
 

Kiorionis

Thoth
Magus de Moderatio
Patron of the Arts
Hermetic Pilgrim
Joined
Jul 5, 2012
Messages
2,727
Drill a hole in the lid and attach a funnel. I have some stoppers so I could plug the hole after I pour the water and remove the funnel. Yeah I like that thanks!

Looked to me like your buckets lid already had a hole with stopper in the middle? I’d am I seeing it weird?

Safety First!
 

Appleheads

Interiora
Hermetic Pilgrim
Mysterious Stranger
Joined
Jan 5, 2024
Messages
50
Here is another video of steam layering process.


Hi Kiorionis, no, there’s no hole or stopper, just an old pickle bucket and lid.

I am going to do a final steam layer process tomorrow. After the final steam, I will start the drying process and voltage checks.